Latest Forum Post
04 Chevy 2500hd tail light issues
Help!!! I have changed my combo switch...
1999 Grand Caravan Sport not starting.
Hi. I'm new here. I hope someone can hel...
Brake Seals Bulging
2021 Toyota Corolla LE 1.8l 65,000 mile...
Engine blew up after oil change, is mechanic responsible?
Hello, I have a 2007 Hyundai Elantra wit...
Changed pads and now brake pedel goes to the floor
I am not much of a mechanic, and needed ...
Equinox air conditioning issue, help please!
I have a 2020 Chevrolet Equinox that has...
2005 Maxima overheats only when idling but engine temp comes down immediately if I rev up the engine (even though car is stationary)
hello everyone, I own a 2005 Nissan M...
Brake & Turn Signal Out - One side only
2002 Ford Ranger 3.0 V6, 5-speed manual ...
Seeking Advice: Strange Noise in 2017 Nissan Versa Note, Mechanic Stumped
Hey everyone, A few weeks ago, my mom's...
Replacing Tires
My daughter just purchased a 2013 Honda ...
|
|
Converting 2008 CX-9 AWD to FWD
|
|
|
| |
|
shomermusar
New User
Mar 3, 2023, 9:47 AM
Post #1 of 3
(2686 views)
|
Converting 2008 CX-9 AWD to FWD
|
Sign In
|
|
2008 Mazda CX-9 3.7 138,000 Hi, I'm want to convert my 2008 CX-9 from AWD to FWD. The hanger bearings for the drive shaft went bad, so I just took the whole shaft out. It's running fine, but now the rear differential is leaking around the CV axle, so it needs CV axle seals. Instead of pouring more money into an AWD system I don't use, can any mechanics answer the following questions? 1. Can I just take the CV axles off and leave the outer housing and spline to keep the bearing together? In other words, I would be taking the CV boot off and pulling the joint out, cleaning all the grease out just leaving the housing where the rollers rest in the spline where the wheel nut attaches. 2. If I do take the axles out, that means the differential will be sitting idle and drained of fluid. The drive shaft isn't connected and the CV axles won't be connected. Will an idle differential throw a traction control fault? 3. Can I unplug the differential and remove it altogether from the car? Will that throw a traction control fault? If so, will traction control still work on the front two wheels if needed? Thanks for any help you are able to offer!
|
|
| |
|
Hammer Time
Ultimate Carjunky
/ Moderator
Mar 3, 2023, 10:01 AM
Post #2 of 3
(2683 views)
|
Re: Converting 2008 CX-9 AWD to FWD
|
Sign In
|
|
This whole idea is ridiculous. If you want a 2WD car, trade this one for a 2WD. Converting it to 2WD is not an option. Everything in this system is integrated into the operating system of the car. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Mar 3, 2023, 10:28 AM
Post #3 of 3
(2676 views)
|
Re: Converting 2008 CX-9 AWD to FWD
|
Sign In
|
|
Agree - NO don't try that AND 98% of folks don't need 4X4 rather buy tires that really work for 2, front or rear drives. The insane costs new then like now insane again costs to fix. Check if whole shaft and "center type bearings if you meant that) can be one swap and rebuilt ready. Leak? Keep it filled enough, find where leaking and add that to fix. If that goes on you over gear oil your stuck - can't use the thing at all - how special (sarcastic,) Tom
|
|
| |
|