|
|
2001 subaru outback clutch trouble
|
|
|
| |
|
|
skatesforcandy
New User
Jul 23, 2009, 7:09 AM
Post #1 of 6
(5058 views)
|
|
2001 subaru outback clutch trouble
|
Sign In
|
|
hello
i'm brian i'm 19years old and i am hoping to begin work on a automotive technology associates degree very soon. i enjoy working with cars and just replaced a transmission with some help from my father in a 97 ford explorer.
anyway just last night i believe my clutch went out in my 2001 subaru outback manual 2 liter 4 cylinder hatchback with 160,000 miles on it. the day before i was parallel parking and the clutch pedal failed to pop back up after i shifted. instead it just stuck to the floor. i began using my foot to pop it back out and it was working alright for the next few drives like that; other than it taking along time to release and occasionally sticking. well last night i attempted to shift from neutral into 2nd and the pedal went straight to the floor with little pressure added. i pulled it up and found again there was no pedal pressure to be found. as it is now i am unable to shift but i can start the car.
can someone give me some advice on where to begin? i'm fairly excited to repair it and understand it could be a very intense job but i don't know where to start. i read on another forum it may just be something behind the dash or in the master/slave cylinders. i do have a service manual right here with me but i'd like a little direction before i begin.
i'd like to add that i know very little terms or anything. i believe the master cylinder controls the brakelines as i replaced one of those in a taurus but i don't know what a slave cylinder is.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jul 23, 2009, 9:27 AM
Post #2 of 6
(5051 views)
|
|
Re: 2001 subaru outback clutch trouble
|
Sign In
|
|
You have a hydraulic clutch system so you have a master cylinder for the clutch also. The slave cylinder is the actuator at the other end of the hydraulic line mounted on the transmission that actuates the clutch.
You most likely have a leak in one or the other and you will have to determine which. I recommend changing both anyway because they usually fail close together.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
skatesforcandy
New User
Jul 23, 2009, 9:57 AM
Post #3 of 6
(5045 views)
|
|
Re: 2001 subaru outback clutch trouble
|
Sign In
|
|
Thank you!! yes i understand now after reading a bit into the service manual. i will begin testing the hydraulic system thoroughly hopefully this afternoon if i get some time. i'll keep you posted.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jul 23, 2009, 10:05 AM
Post #4 of 6
(5042 views)
|
|
Re: 2001 subaru outback clutch trouble
|
Sign In
|
|
Assuming the reservoir has gone dry, just look for a small bit of wetness either at the back of the master in the engine compartment or under the dash where the rod comes through. If nothing there, look under the boot of the slave for any wetness to indicate a leak.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
skatesforcandy
New User
Aug 1, 2009, 2:02 PM
Post #5 of 6
(5016 views)
|
|
Re: 2001 subaru outback clutch trouble
|
Sign In
|
|
alright so i've run into a few difficulties now that i finally have been able to work on my vehicle. NUMBER 1: i was working on replacing my clutch master cylinder and when pulling out the pin that connects it to the pedal mechanism i was careless and the pin dissappeared. can this be replaced? i don't mean the bolt type pin but the thin wire that holds it in place.
NUMBER 2: The clutch master cylinder i ordered has a hole in the very back of it with a bronze ummmm bolty tubey type thing. the damaged one does not have this. i type in my car's info and i keep getting the cylinder with the bolty thing in back. this is what i bought http://www.drivewire.com/products/subaru-outback/clutch-master-cylinder/414/
It's exactly the same except for the boltey thing in back under the reservoir. i can't even find the right part. is this boltey thing a problem?
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Aug 1, 2009, 2:07 PM
Post #6 of 6
(5013 views)
|
|
Re: 2001 subaru outback clutch trouble
|
Sign In
|
|
If your talking about that fitting at the very end of the cylinder, that's a bleeder. It's there to help you bleed the system after replacing it.
The clip you lost is just a hair pin clip and you can buy them at most auto parts stores
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
(This post was edited by Hammer Time on Aug 1, 2009, 2:15 PM)
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
Drive Shaft Repair
2006 Toyoto Camry XLE Driver Side Electric Window Trouble
Grounding Cable, 2017 Jeep Renegade Trailhawk
equipment
Howdy
