|
|
XCWX1
Novice
Oct 15, 2011, 7:45 PM
Post #1 of 12
(5548 views)
|
|
1986 Mazda B2000 pickup
|
Sign In
|
|
1986 Mazda B2000 pickup
Just put in a rebuilt manual 5 speed transmission and new clutch. Runs great until I have run it for awhile and then it starts shuttering when pulling off.
What do I need to replace?
|
|
| |
|
|
Mr.scotty
Enthusiast
Oct 15, 2011, 8:24 PM
Post #2 of 12
(5520 views)
|
|
Re: 1986 Mazda B2000 pickup
|
Sign In
|
|
Did you bring the flywheel to a machine shop before installing the new clutch?
--------------------------------------------------------
Your only as good as your tools!
|
|
| |
|
|
XCWX1
Novice
Oct 15, 2011, 8:26 PM
Post #3 of 12
(5519 views)
|
|
Re: 1986 Mazda B2000 pickup
|
Sign In
|
|
No I didnt ..
|
|
| |
|
|
Mr.scotty
Enthusiast
Oct 15, 2011, 8:27 PM
Post #4 of 12
(5517 views)
|
|
Re: 1986 Mazda B2000 pickup
|
Sign In
|
|
Then you will probably have to do the job over again.
--------------------------------------------------------
Your only as good as your tools!
|
|
| |
|
|
XCWX1
Novice
Oct 15, 2011, 8:40 PM
Post #5 of 12
(5512 views)
|
|
Re: 1986 Mazda B2000 pickup
|
Sign In
|
|
I am probably getting ready to pull the engine and transmission. Am I going to have to replace the clutch and machine the flywheel? or just machine the flywheel?
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Oct 15, 2011, 8:45 PM
Post #6 of 12
(5509 views)
|
|
Re: 1986 Mazda B2000 pickup
|
Sign In
|
|
It depends on the reason for the shuddering......
If there was oil leaking onto it or some other contamination problem then it would problably be a good idea to change it out while the engine is out, it'll never be any easier to do.
If the flywheel is just scored & the disc looks good, since you said it was "brand new" then you could probably reuse it....
|
|
| |
|
|
XCWX1
Novice
Oct 15, 2011, 9:34 PM
Post #7 of 12
(5504 views)
|
|
Re: 1986 Mazda B2000 pickup
|
Sign In
|
|
I put the clutch in maybe 3 months ago. Replaced the rear seal, transmission and clutch. The shuttering didnt start until a month ago I guess.
|
|
| |
|
|
Mr.scotty
Enthusiast
Oct 16, 2011, 8:05 AM
Post #8 of 12
(5496 views)
|
|
Re: 1986 Mazda B2000 pickup
|
Sign In
|
|
The clutch disck may be fine then.
You'll just have to find out when you pull her apart.
--------------------------------------------------------
Your only as good as your tools!
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Oct 16, 2011, 3:36 PM
Post #9 of 12
(5488 views)
|
|
Re: 1986 Mazda B2000 pickup
|
Sign In
|
|
As mentioned......If nothing has leaked onto it, you "should" be fine going with the old one.
If by chance something has leaked onto the disk, don't make the mistake thinking you can just clean it up..... You can sand it & spray it off with brk clean & it will "look" fine but the disk is like a sponge so it will have absorbed whatever it was & it will come back to haunt you down the road.......
|
|
| |
|
|
synchro
User
Oct 16, 2011, 5:58 PM
Post #10 of 12
(5479 views)
|
|
Re: 1986 Mazda B2000 pickup
|
Sign In
|
|
Depends, Is the disc organic or ceramic?
|
|
| |
|
|
XCWX1
Novice
Oct 18, 2011, 6:31 PM
Post #11 of 12
(5465 views)
|
|
Re: 1986 Mazda B2000 pickup
|
Sign In
|
|
Checked today. Flywheel needs turning everything else looks fine.
Thanks all.
|
|
| |
|
|
Mr.scotty
Enthusiast
Oct 18, 2011, 8:31 PM
Post #12 of 12
(5458 views)
|
|
Re: 1986 Mazda B2000 pickup
|
Sign In
|
|
Yup, Thats what we're here for.
--------------------------------------------------------
Your only as good as your tools!
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
Car idles funny but doesn't throw codes
Rear brake retaining clips
speedometer wild deflections; sometime pump gas
Car stalling problem
