|
|
Edwardh4
Novice
Jan 4, 2014, 8:40 PM
Post #1 of 9
(1640 views)
|
On a 02 avalanche, 5.3 with 160k. has sat up for 8 months. Installed A new fuel pump. It will give a split second start then kill. The security light is not staying on but does blink like normal. The fuel gauge is reading on empty and the low fuel light is on. I can smell fuel after trying to start it several times so Its getting fuel. Also if I press accelerator to the floor it will not give me the split second start. I have performed the anti theft relearn procedure. PLEASE help!!!!!!!!!!!!! I hope I have givin enough info, thank y'all for being here.
|
|
| |
|
|
GC
User
Jan 4, 2014, 9:47 PM
Post #2 of 9
(1612 views)
|
|
Re: No start issue
|
Sign In
|
|
Are you sure that it has enough fuel in the tank? What is your fuel pressure? Did it run before replacing pump?
Check this thread
http://autoforums.carjunky.com/...LL_NOT_START_P75655/
____________________________________________________
Willing to help, willing to learn... Rob
(This post was edited by goiserclause on Jan 4, 2014, 9:50 PM)
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Jan 5, 2014, 12:51 AM
Post #3 of 9
(1600 views)
|
|
Re: No start issue
|
Sign In
|
|
If the theft light is flashing, that means the immobilizer is active. Either there is something wrong with the key or the PCM lost communications with the theft deterent module. You will probably need to get it towed to a shop that can access the BCM and other modules with a high end scan tool to see what kind of code(s) are being stored and to do some diagnosis to see what is actually going on.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Jan 5, 2014, 12:53 AM)
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jan 5, 2014, 7:18 AM
Post #4 of 9
(1592 views)
|
|
Re: No start issue
|
Sign In
|
|
DS is right. The immobilizer is shutting you down.
Did you do the complete 30 minute relearn or just the 10 minute?
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Edwardh4
Novice
Jan 5, 2014, 8:31 AM
Post #5 of 9
(1588 views)
|
|
Re: No start issue
|
Sign In
|
|
Yessir, I did the 30 minute. One thing that puzzles me is this, when I crank it with my foot off the gas it will do the split second start, with my foot on the gas, it won't?? Also I know there is atleast 8 gallons of gas and the fuel level is still below Empty and the low fuel light is on.
Thanks again for the help guys!!!
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jan 5, 2014, 8:50 AM
Post #6 of 9
(1584 views)
|
|
Re: No start issue
|
Sign In
|
|
Did you get the correct response when doing the procedure?
Did the security light go off at the end of each segment?
Have you tried a different key?
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
(This post was edited by Hammer Time on Jan 5, 2014, 8:50 AM)
|
|
| |
|
|
Edwardh4
Novice
Jan 5, 2014, 9:39 AM
Post #7 of 9
(1580 views)
|
|
Re: No start issue
|
Sign In
|
|
The light did not stop blinking. I used the same key. Should I try the reset with another key?
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jan 5, 2014, 10:27 AM
Post #8 of 9
(1576 views)
|
|
Re: No start issue
|
Sign In
|
|
If the light did not stop blinking, then you didn't complete a relearn. You don't proceed to the next step until the light stops blinking.
I'll give you the procedure in case you're doing it wrong.
PASSLOCK 30 MINUTE RELEARN
Disconnect the battery and hold the cables together for about 30 seconds then reconnect the cables before performing the procedure.Read it carefully if done incorrectly it won't work.
Turn ON the ignition, with the engine OFF.
Attempt to start the engine, then release the key to ON (vehicle will not start).
Observe the SECURITY telltale, after approximately 10 minutes the telltale will turn OFF.
Turn OFF the ignition, and wait 5 seconds.
Repeat steps 1 through 4 two more times for a total of 3 cycles/30 minutes (the vehicle is now ready to relearn the Passlock™ Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK).
Important
The vehicle learns the Passlock™ Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.
Start the engine (the vehicle has now learned the Passlock™ Sensor Data Code and/or password).
With a scan tool, clear any DTCs if needed (history DTCs will self clear after 100 ignition cycles).
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
| | |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
2006 Toyoto Camry XLE Driver Side Electric Window Trouble
Tierod end change caused some kind of leak
Grounding Cable, 2017 Jeep Renegade Trailhawk
equipment
Howdy
