|
|
Guest
Anonymous Poster
Apr 20, 2007, 10:34 AM
Post #1 of 7
(1290 views)
|
|
Brake Pad replacement ?
|
Sign In
|
|
Hi all,
Has anyone replaced the rear brake pads on a peugeot 307 SW.
I bought the pads thinking it would be easy but I can't get the piston to go back into the caliper. 
I can only assume that there is a none return valve, maybe connected to the hand brake. 
Either way I can't get the sods back in to replace the pads 
Any help would be appreciated 
|
|
| |
|
|
DanD
Veteran
/ Moderator
Apr 20, 2007, 12:02 PM
Post #2 of 7
(1286 views)
|
|
Re: Brake Pad replacement ?
|
Sign In
|
|
If the parking brake works through the caliper, the caliper’s piston needs to be rotated in the bore and compressed at the same time to get them to retract.
Dan.
Canadian "EH"
|
|
| |
|
|
Guest
Anonymous Poster
Apr 20, 2007, 12:05 PM
Post #3 of 7
(1284 views)
|
|
Re: Brake Pad replacement ?
|
Sign In
|
|
I think that you've got it, thanks Dan.
Although I suspect that I also have to open the bleed screw
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Apr 20, 2007, 2:48 PM
Post #4 of 7
(1281 views)
|
|
Re: Brake Pad replacement ?
|
Sign In
|
|
It's best to bleed it out while retracting as you are not pushing old brake fluid back to the master cylinder. If you do that and don't intend on bleeding the whole system put a clear tube into a clean glass container from the bleeder and keep it submerged or air may get drawn back in.
It's a good time to just replace rotors as most don't have lots of extra metal to turn them,
T
|
|
| |
|
|
Guest
Anonymous Poster
Apr 22, 2007, 6:39 AM
Post #5 of 7
(1273 views)
|
|
Re: Brake Pad replacement ?
|
Sign In
|
|
First off thanks for all your help.
This morning I loaded my tools into the car and set off to work (far easier to do this kind of job on a flat concrete floor with a big equiped workshop at hand).
So.......... yes the pistons must be twisted (clockwise), at thesame time as pressing them and yes once you know how its a piece of piss (excuse my french).
I had intentions of grinding the head of a bolt so that it would fit the piston head but as it turned out I took the easy option and...........
.........twisted the piston with a big pair of adjustable pliers (taking care not to damage the aluminium piston head), and pressed the piston in by turning (by hand), a big bolt I found in a disused factory next door (yes that easy).
Where things went a little wrong was I put a clamp on the brake hose so that I could bleed the old fluide out at thesame time but it would seem that under the rubber they are braided and so I flattened the tube a little. I did put the clamp on at 90° and that seems to of made my round hose into a square one.
However the good news is that they work 
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Apr 22, 2007, 6:54 AM
Post #6 of 7
(1271 views)
|
|
Re: Brake Pad replacement ?
|
Sign In
|
|
Keep an eye on that hose or just replace it. It has been compremised,
T
|
|
| |
|
|
Guest
Anonymous Poster
Apr 22, 2007, 9:08 AM
Post #7 of 7
(1269 views)
|
|
Re: Brake Pad replacement ?
|
Sign In
|
|
Will do
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
Drive Shaft Repair
2006 Toyoto Camry XLE Driver Side Electric Window Trouble
Grounding Cable, 2017 Jeep Renegade Trailhawk
equipment
Howdy
