Connect

Car Pictures

Shopping

Classifieds

News & Articles

Car Forums

Automotive Links

(Bookmark CarJunky)

	Auto Repair Home	SEARCH POSTS	WHO'S ONLINE	LOG IN

Automotive Repair Car Troubleshooting Topics   Car Troubleshooting   Engine Troubleshooting   Engine Fault Codes   Electrical and Wiring   Transmission Problems Car Repair Topics   Car Making Noises   Car Stereo Repair   Heating or AC Issues   Motorcycles and ATVs   Tricks of the Trade   Truck Repair Advice Site Options:      Login   Sign up here! Latest Forum Post   mdma pills for sale : WhatsApp +33758633852 ketamine, 4-MMC, MDPV, methylone, amphet...   Buy Nembutal Oral Solution Pentobarbital.. WhatsApp +33758633852 order nembutal online in Germany (WhatsA...   Drive Shaft Repair I have a 2015 Chevy Traverse AWD. The fr...   2006 Toyoto Camry XLE Driver Side Electric Window Trouble Hello, Looking for a little brain help ...   Tierod end change caused some kind of leak Hello so I just took my car to the nearb...   2011 Dodge Nitro OBD scanner seems to drain battery in 10-20 minutes When I bought this car in summer 2023, a... Grounding Cable, 2017 Jeep Renegade Trailhawk The Cable that connects my negative batt... Rough Idle (Found new thing) Hi everyone. First of all sorry for bad ...     equipment hey yall. im a first year engineering st...   HELP I have a 1956 1/2 ton panel truck, 69 35...

Search Auto Parts Search 92 ford explorer manuel trans Sign up here!   Email This Post Auto Repair Home>> Automotive Repair>> Car Troubleshooting Guest Anonymous Poster roarkwee4@comcast.net Sep 15, 2008, 3:15 AM Post #1 of 5 (2338 views) 92 ford explorer manuel trans Sign In I removed the trans to replace the clutch. It would not go into 1st or 2nd gear after the clutch replace. I removed the sensor opposite side of the neutral safety switch prior to the removal(realized I did not need to after trans was down). If I take that sensor out it will go into 1st and 2nd fine. But as soon as I replace it, it binds the shifter and will not go into 1st and 2nd gear. I can feel a pin moving back and forth if someone shift while I have the tip of my finger in the hole.Is there a way to reset the pin? Please respond to this form my email is not working Jeff Norfolk Enthusiast Sep 15, 2008, 10:01 AM Post #2 of 5 (2330 views) Re: 92 ford explorer manuel trans Sign In Yikes. Keep your finger out of the side of the trans while people are trying to shift it. Good way to lose the tip!. If you put the sensor back in and try to shift into 1 or 2 with the engine not running will it go? Jeff Guest Anonymous Poster Sep 15, 2008, 12:31 PM Post #3 of 5 (2325 views) Re: 92 ford explorer manuel trans Sign In No it will not. I have tried to put the sensor in while it is in 1st gear 2nd gear and neutral. As soon as I shift first time back to normal. I should have said tip was over the hole not in it. Believe me I know not to put it in harms way. Jeff Norfolk Enthusiast Sep 15, 2008, 2:13 PM Post #4 of 5 (2322 views) Re: 92 ford explorer manuel trans Sign In This has an internal slave cylinder that requires disconnecting when removing trans. Have you tried bleeding the system yet? Also these systems are a bit tricky. I have had to remove the clutch master cylinder and bench bleed it before to get one to work for me. It will come out resevoir and all. What you have to do is hang it in a way that all of the air will rise to the top and the fluid will run out of the connection the goes into the slave cylinder. Once you are there, push the center of the connection that goes into the slave cylinder so that fluid runs out. I use a 1/4 inch drive extension. Do this until the fluid comes out clean. You may have to fill it up a few times. Jeff Guest Anonymous Poster Sep 15, 2008, 3:46 PM Post #5 of 5 (2321 views) Re: 92 ford explorer manuel trans Sign In Thanks for the replys. I did not disconnect the hydraulic line. I just moved the trans back and supported on jack stands and a jack. I was doing it by myself and did not want to lift that big thing by myself. All the other gears were working fine. So bleeding would not have been the problem. I gave it another go this evening. I removed the sensor again. Then I put the truck in 1 st gear. Then reinstalled the sensor. It seems to be working fine now. I am guessing the one who was helping me the first time did not have it in either gear when I put the sensor back in the first two times( not familar with a stick shift). Have my finger crossed that it is a long term fix. I would hate to pull the trans again.   Email This Post   Automotive Repair     Auto Body Repair and Refinishing     Heating or AC Issues     Electrical and Wiring     Brake Systems     Car Stereo Repair Advice     General Discussions     Car Making Funny Noises     Engine Fault Codes     Engine Troubles     Exhaust Systems     Steering and Suspension     Transmission Troubles     Tricks of the Trade Automotive World     General Discussions     Antique Car Talk     Car Shows and Events     The Bargin Bin     Motor Vehicle Inspection     Car Care Tips     Traffic Tickets     Gasoline, Motor Oils, Concept Cars and Engines     Auto Insurance, Financing, Leases, Warranties Truck Repair     General Discussions     Truck Engine Repair     Truck Suspension Repair Motorcycle Repair     General Discussions     Motorcycle Engine Repair CarJunky     Open Posting     Board FAQ's     New Board Suggestions

Search this forum this category all forums for All words Any words Whole Phrase (options)

Privacy Sitemap