Latest Forum Post
Buy Dilaudid,Oxycodone,Adderall (ordermcatonline@gmail.com)
https://opioidsmeds.com Email: sales@op...
comprar éxtasis MDMA, comprar efedrina en polvo (ordermcatonline@gmail.com)
https://opioidesmeds.com Correo electró...
Compre Nembutal, anfetamina, metanfetamina (ordermcatonline@gmail.com)
https://opioidsmeds.com E-mail: sales@op...
comprar éxtasis MDMA, comprar efedrina en polvo https://opioidesmeds.com
https://opioidesmeds.com Correo electró...
mephedrone 4mmc till salu,Köp mephedrone 4mmc online (ordermcatonline@gmail.com)
https://opioidsmeds.com E-post: sales@op...
Drive Shaft Repair
I have a 2015 Chevy Traverse AWD. The fr...
2006 Toyoto Camry XLE Driver Side Electric Window Trouble
Hello, Looking for a little brain help ...
Tierod end change caused some kind of leak
Hello so I just took my car to the nearb...
2011 Dodge Nitro OBD scanner seems to drain battery in 10-20 minutes
When I bought this car in summer 2023, a...
Grounding Cable, 2017 Jeep Renegade Trailhawk
The Cable that connects my negative batt...
|
|
1990 chevy beretta key/tumbler replacment
|
|
|
| |
|
shiftyvigilante
Anonymous Poster
bbrookhart@hotmail.com
May 1, 2006, 1:53 PM
Post #1 of 4
(4135 views)
|
1990 chevy beretta key/tumbler replacment
|
Sign In
|
|
ok, i gotta 1990 beretta and the tumbler went haywire (stopped grabbing starting linkage). so i need to replace it w/a new one but cant get the old one out. i have already taken off the steering wheel along w/the underneath dash plate and still can not reach or see a release key/pin or any type of screws...can someone please walk me through the removal and any do's and dont's of replacing key-tumblers on this make and model???
|
|
| |
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
May 2, 2006, 12:19 AM
Post #2 of 4
(4129 views)
|
Re: 1990 chevy beretta key/tumbler replacment
|
Sign In
|
|
FIRST! If this car has an air bag just take it somewhere! If not you can replace the whole thing pretty cheap with a new lock but you will need a steering wheel puller which may not be too expensive or rentable. There is probably a wire ring the retains the wheel lock device and don't lose that. I've removed them with two screwdrivers, snap ring pliers and bad language! Last one I replaced on a GM was because of all keys lost but not broken. There will be some retaining bolt or screw for the whole lock cylinder - then it's easy. T
|
|
| |
|
DanD
Veteran
/ Moderator
May 2, 2006, 4:26 AM
Post #3 of 4
(4126 views)
|
Re: 1990 chevy beretta key/tumbler replacment
|
Sign In
|
|
I believe that the Beretta had the square column in them, which are a little different to take apart. After the wheel is removed you should see one retaining screw that holds the turn signal housing #28 on and the hazard switch knob#27; with those two removed the housing should slide up and off the column. It’s a tight fit so you’ll have to give it a bit of effort to get it to slide up. Then you may have to remove the turn signal #26 retaining screws and position the switch out of the way to get at the ignition lock retaining screw. You’ll also have to remove the key buzzer contacts #8, it'll jam the lock on the way out. Turn the ignition lock to the accessory position and with the retainer and buzzer removed the lock should slide out. One of two things happens to this style of columns, one is the half round gear at the end of the ignition lock breaks free from the lock which is the easy fix with a new lock. But what usually breaks is the actuator rod rack #3 that means disassembling a lot more of the column to get at it. If it is this rack that’s broken you will likely want to remove the complete column from the car, makes the disassembly of the column a whole lot easier. Check with the dealer if this rack is still available with the age of this car it may not be. If this is the case head to the auto wreckers (salvage yards for you yanks LOL) and swap out the complete column. Or that’s what I would do. Keep it fun; the first one I had to disassemble was kind of a challenge but not undoable. Dan. Canadian "EH"
(This post was edited by DanD on May 2, 2006, 4:31 AM)
|
|
| |
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
May 2, 2006, 8:06 AM
Post #4 of 4
(4118 views)
|
Re: 1990 chevy beretta key/tumbler replacment
|
Sign In
|
|
Dan would know better about this than the ones I've dealt with. Not many but have the pullers for the ones I did. Just funny: I did one in a parking lot of a busy store and broke into the car and fixed it on location and not one person questioned what I was doing!! I could have taken off with that car when I was done - like stolen. Bless it - there are still some places where people just trust each other. T
|
|
| |
|