Main IndexAuto Repair Home Search Posts SEARCH
POSTS 		Who's Online WHO'S
ONLINE 		Log in LOG
IN




Automotive Repair
Car Troubleshooting Topics
  Car Troubleshooting
  Engine Troubleshooting
  Engine Fault Codes
  Electrical and Wiring
  Transmission Problems

Car Repair Topics
  Car Making Noises
  Car Stereo Repair
  Heating or AC Issues
  Motorcycles and ATVs
  Tricks of the Trade
  Truck Repair Advice

Site Options:   
  Login
  Sign up here!



Latest Forum Post
hot_with_replies.gif image  locked   Car idles funny but doesn't throw codes
2006 Hyundai Elantra Engine size: 2.0L m...

no_replies.gif image   Rear brake retaining clips
2015 Toyota Camry. I bought Import Direc...

no_replies.gif image   Sanded rotors (deep scratches)
I'm new to the forum and I have a couple...

no_replies.gif image   2010 Mazda 3 Electrical Going On and Off while driving
I drive a 2010 Mazda 3. It's always been...

hot_with_replies.gif image   Code P0193 Fuel Rail Pressure Sensor Circuit High Bank 1
2004 Ford E-350 Super Duty Ext Cargo Van...

with_replies.gif image   speedometer wild deflections; sometime pump gas
1999 Gmc Savana, rwd, 5.7 (I think) v8 ...

with_replies.gif image  locked wrench.gif Car stalling problem
My 2013 hyundai started losing power whe...

hot_with_replies.gif image   2018 Kia soul. Knocking while accelerating.
Hello, my 2018 Kia soul started making t...

with_replies.gif image  locked   2005 Buick Lesabre surging
My 2005 Buick Lesabre runs good & th...

with_replies.gif image wrench.gif Misfire on coil E
I am new to this forum. I haven't figure...




engine wont crank by hand

Search for (search options)
 



rrtdiesel
New User

Oct 31, 2010, 12:41 PM

Post #1 of 7 (1853 views)
engine wont crank by hand Sign In
2000 Ford Ranger
3.0L 142000 miles
4x4

pulled motor to replace oil pump.. engine was turning by hand then reconnected block to transmission now the engine wont budge....truck is in neutral....any ideas?


Sidom
Veteran / Moderator
Sidom profile image

Oct 31, 2010, 2:57 PM

Post #2 of 7 (1842 views)
Re: engine wont crank by hand Sign In
Auto or manual tranny?
If it's manual does pushing the clutch pedal make any difference?
Also when was the last time it would turn over by hand?
After the pan was put back on?
Does pulling the starter make any difference?
Does removing the serp belt make a difference?


(This post was edited by Sidom on Oct 31, 2010, 2:57 PM)


rrtdiesel
New User

Oct 31, 2010, 3:37 PM

Post #3 of 7 (1836 views)
Re: engine wont crank by hand Sign In
Automatic tranny
turning over after the pan was put back on
starter and the serp belt are removed


re-tired
Veteran / Moderator
re-tired profile image

Oct 31, 2010, 4:35 PM

Post #4 of 7 (1832 views)
Re: engine wont crank by hand Sign In
How were you able to rotate the erngine to bolt up the torque coinverter?


LIFE'S SHORT GO FISH


re-tired
Veteran / Moderator
re-tired profile image

Nov 1, 2010, 6:21 PM

Post #5 of 7 (1814 views)
Re: engine wont crank by hand Sign In
check to see if torque converter is fully seated in trans . back off bell housing bolts ,if eng now tiurns you need to drop tranny and rotate and push in converter till seated in pump.


LIFE'S SHORT GO FISH


chickenhouse
Enthusiast

Nov 1, 2010, 6:25 PM

Post #6 of 7 (1812 views)
Re: engine wont crank by hand Sign In
Hey RT, do they still do these like te old 289's, meaning you have to line up the torque convertor drain plug with the hole in the flex plate? Otherwise you have this prob?


re-tired
Veteran / Moderator
re-tired profile image

Nov 1, 2010, 6:41 PM

Post #7 of 7 (1810 views)
Re: engine wont crank by hand Sign In
to the best of my knowledge not on this model . however it is easy for a converter to slip out a bit.


LIFE'S SHORT GO FISH





 
 
 






Search for (options) Privacy Sitemap