|
|
|
dodge intrepid problems....HELP
|
|
|
| |
|
|
badass 87
User
Dec 7, 2011, 7:15 AM
Post #1 of 20
(4774 views)
|
|
dodge intrepid problems....HELP
|
Sign In
|
|
i have a 2002 dodge intrepid with a 2.7 engine...when i bought the car the engine had blown head gaskets and a bad water pump....it seemed to run fine other than that....we pulled the engine for a rebuild...new chain rods mains valve job water pump guides ......we put the engine back in ....it began to start hard...found bad ground....still starts hard....but the main problem we are having is that when you do get it started and start to drive it runs fine but will not accelerate past 2400 rpm....it acts like it kills the fuel....you let off the gas and go below 2400 all is fine ,,,,runs good...does this all the time....we have replaced the computer....crank sensor .....cam sensor....nuetral safety swith...still nothing seems to help....
please scratch ur heads along with me and collectively maybe we can fix my problem
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Dec 7, 2011, 7:24 AM
Post #2 of 20
(4760 views)
|
|
Re: dodge intrepid problems....HELP
|
Sign In
|
|
I would use a scan tool to see what gear the computer is seeing. If there is a problem with the transmission range sensor and the PCM thinks it is in Park/Neutral, it will engage the rev limiter.
You also want to verify proper fuel pressure.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
badass 87
User
Dec 7, 2011, 7:39 AM
Post #3 of 20
(4752 views)
|
|
Re: dodge intrepid problems....HELP
|
Sign In
|
|
feul pressure has been checked..is good...like i said the safety switch has been changed...
|
|
| |
|
|
badass 87
User
Dec 7, 2011, 8:00 AM
Post #4 of 20
(4748 views)
|
|
Re: dodge intrepid problems....HELP
|
Sign In
|
|
scanner shows proper gear selection...but in park the reverse lights r on?
|
|
| |
|
|
badass 87
User
Dec 7, 2011, 9:27 AM
Post #6 of 20
(4726 views)
|
|
Re: dodge intrepid problems....HELP
|
Sign In
|
|
gear selector and scanner say the gear at same time
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Dec 7, 2011, 10:00 AM
Post #7 of 20
(4719 views)
|
|
Re: dodge intrepid problems....HELP
|
Sign In
|
|
Have you taken the transmission apart?
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
badass 87
User
Dec 7, 2011, 2:47 PM
Post #8 of 20
(4708 views)
|
|
Re: dodge intrepid problems....HELP
|
Sign In
|
|
ONLY TO PUT NUETRAL SWITCH IN
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Dec 7, 2011, 3:05 PM
Post #9 of 20
(4706 views)
|
|
Re: dodge intrepid problems....HELP
|
Sign In
|
|
Is there any codes??? P0016???
|
|
| |
|
|
badass 87
User
Dec 8, 2011, 1:23 PM
Post #10 of 20
(4689 views)
|
|
Re: dodge intrepid problems....HELP
|
Sign In
|
|
JUST PUT my ethos snap on scanner on it... codes as follows
po340 camshaft position sensor cicuit A BANK 1 OR SINGLE SENSOR
po344 camshaft position sensor circuit A intermittent bank 1 or single sensor
po 016 crankshaft position- camshaft position correlation bank 1 sensor A
parts we have replaaced.....2 camshaft sensors.....2 crankshaft sensors.....computer and neutral safety switch...
I AM lost
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Dec 8, 2011, 1:28 PM
Post #11 of 20
(4688 views)
|
|
Re: dodge intrepid problems....HELP
|
Sign In
|
|
You might be out of time....I've seen that P0016 when they have jumped time....
Take a vacuum reading, if it's low & shaky, that not good.......Take a look at the fuel trims and post the data if you can...
Try disconnecting the cmp and see if it will start & run and if that makes a difference.....
|
|
| |
|
|
badass 87
User
Dec 8, 2011, 1:36 PM
Post #12 of 20
(4685 views)
|
|
Re: dodge intrepid problems....HELP
|
Sign In
|
|
timming has been checked
|
|
| |
|
|
badass 87
User
Dec 8, 2011, 1:44 PM
Post #13 of 20
(4683 views)
|
|
Re: dodge intrepid problems....HELP
|
Sign In
|
|
whats the cmp...to ask a stupid
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Dec 8, 2011, 1:45 PM
Post #14 of 20
(4682 views)
|
|
Re: dodge intrepid problems....HELP
|
Sign In
|
|
Try disconnecting the cmp and see if that makes a difference, it may or may not start, some need the cmp others don't.. If you have access to a scope, use 2 channels & scope both the ckp & cmp to see if there are in sync...Also look at the other data I mentioned and post it if you can...
Is there any knocking noise from the timing cover.....The tensioners on those 2.7 can be a little tricky to set if you aren't familiar with them.....
|
|
| |
|
|
badass 87
User
Dec 8, 2011, 1:47 PM
Post #15 of 20
(4677 views)
|
|
Re: dodge intrepid problems....HELP
|
Sign In
|
|
we have done several of these engines and never had these problems,
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Dec 8, 2011, 1:47 PM
Post #16 of 20
(4677 views)
|
|
Re: dodge intrepid problems....HELP
|
Sign In
|
|
cmp=camshaft position sensor ckp=crankshaft position sensor
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Dec 8, 2011, 1:49 PM
Post #17 of 20
(4674 views)
|
|
Re: dodge intrepid problems....HELP
|
Sign In
|
|
Was the the flywheel that came with this engine reused, or was a different one installed????
|
|
| |
|
|
badass 87
User
Dec 8, 2011, 2:25 PM
Post #18 of 20
(4666 views)
|
|
Re: dodge intrepid problems....HELP
|
Sign In
|
|
same
|
|
| |
|
|
badass 87
User
Dec 13, 2011, 8:07 AM
Post #19 of 20
(4635 views)
|
|
Re: dodge intrepid problems....HELP
|
Sign In
|
|
like i said...this car runs like a top...no sputtering misfires or anythinh
g...sometimesa hard to start..sometimes not...just will not accelerate past 2400rpm....could a bad battery cause this issue?
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Dec 13, 2011, 2:03 PM
Post #20 of 20
(4624 views)
|
|
Re: dodge intrepid problems....HELP
|
Sign In
|
|
I've suggested, a few times now, to disconnect the cmp and see if that makes a difference.....I was waiting on a reply to what happened when you did this.....I also wanted to know if you had/have access to a scope....
One thing I will mention you can also do (and post back & let us know what you found) since you were having the rev lights coming on at the wrong time, double check all the wiring harnesses to make sure none of them got pinched or damaged when the engine was reinstalled....
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
Strut spring orientation and strut mount tension nut
Please Help - Knock sound & engine fail
Brake Seals Bulging
