92 isuzu rodeo clutch problem - Engine Troubleshooting


	Auto Repair Home	SEARCH POSTS	WHO'S ONLINE	LOG IN

Automotive Repair

Car Troubleshooting Topics
  Car Troubleshooting
  Engine Troubleshooting
  Engine Fault Codes
  Electrical and Wiring
  Transmission Problems

Car Repair Topics
  Car Making Noises
  Car Stereo Repair
  Heating or AC Issues
  Motorcycles and ATVs
  Tricks of the Trade
  Truck Repair Advice

Site Options:
  Login
  Sign up here!

Latest Forum Post

Drive Shaft Repair

I have a 2015 Chevy Traverse AWD. The fr...

2006 Toyoto Camry XLE Driver Side Electric Window Trouble

Hello, Looking for a little brain help ...

Tierod end change caused some kind of leak

Hello so I just took my car to the nearb...

2011 Dodge Nitro OBD scanner seems to drain battery in 10-20 minutes

When I bought this car in summer 2023, a...

Grounding Cable, 2017 Jeep Renegade Trailhawk

The Cable that connects my negative batt...

Rough Idle (Found new thing)

Hi everyone. First of all sorry for bad ...

equipment

hey yall. im a first year engineering st...

HELP

I have a 1956 1/2 ton panel truck, 69 35...

Howdy

    Just wanted to s...

ABS/Tractiob/Brake Lights on But No DTCs

Hello all, Recently while driving m...

92 isuzu rodeo clutch problem

Sign up here!

Email This Post

Auto Repair Home>> Automotive Repair>> Engine Troubleshooting

enewman
New User

Jan 13, 2007, 8:46 PM

Post #1 of 6 (2789 views)

92 isuzu rodeo clutch problem	Sign In

I just replced my cluth/pressure plate/throw out bearing and had the fly wheel resurfaced. also replaced the slave cylinder. I am unable to get the car to go into gear. Have tried adjusting the free play and bled the master and slave multiple times..no luck. Aside from droping the transmision again and double checking..lets asume everything is right..Any suggestions? It is on a 92 isuzu rodeo 3.1L 4x4 with the 9 11/16 clutch.

Tom Greenleaf
Ultimate Carjunky / Moderator
Tom Greenleaf profile image

Jan 14, 2007, 12:09 AM

Post #2 of 6 (2784 views)

Re: 92 isuzu rodeo clutch problem	Sign In

Guess: This is probably a problem with the hydraulic linkage to properly disengage the clutch.

Other: If trans was allowed to bend up the clutch disk by hanging there until you bolted it up it will just drag all the time and make shifting tough and a new disk is the only fix. Hope it's simpler than going back there, T

enewman
New User

Jan 14, 2007, 1:13 AM

Post #3 of 6 (2783 views)

Re: 92 isuzu rodeo clutch problem	Sign In

kinda what i was thinkin to...will let you know what i find..

enewman
New User

Jan 29, 2007, 10:53 PM

Post #4 of 6 (2767 views)

Re: 92 isuzu rodeo clutch problem	Sign In

Well turns out I was given the wrong clutch..once we pulled it out ..again...it had to many springs and was off by 1/8 if an inch..not sure if it was even for an Isuzu..a hard lesson re-learned( I knew better than to just throw a new part in before checking)..so to everyone who sees this..DOUBLE CHECK THE PARTS!!!

tut2261
User

Jan 29, 2007, 11:39 PM

Post #5 of 6 (2765 views)

Re: 92 isuzu rodeo clutch problem	Sign In

I hear that, I installed 4, Ford "Reman" Clutch kits in a 95 F-150 all within 10 miles. Before a Ford Engineer agreed with me that the pressure plates where machined and the friction surface was not flat. All it took was a new clutch kit from napa.
The uneven surface of the pressure plate would not allow the clutch to fully dis-engauge.
Needless to say I will never install a "Reman" clutch again.

Tom Greenleaf
Ultimate Carjunky / Moderator
Tom Greenleaf profile image

Jan 30, 2007, 9:24 PM

Post #6 of 6 (2756 views)

Re: 92 isuzu rodeo clutch problem	Sign In

Parts can be a real pest!! When I call my very local store I bring the old one with me if there are choices in the same vehicle. This has happened to me too many times over the years so I match them up at the counter.

Note: Some times you'll be asked the month of production which can be found on most door jams, T

Email This Post

Search for (options) Privacy Sitemap