|
|
PeteOh
New User
Apr 23, 2008, 11:36 AM
Post #1 of 10
(1315 views)
|
turnsgnal dont Blink
|
Sign In
|
|
I have a Buick Century 2000. The 4-ways blink fine. All the correct lights go on when turn lever is shifted BUT dont blink. I found the 4 way blinker relay and "supposedly' there is another like it which I can not find. I looked hard - not under dash near the other one, and not in the relay blocks. Last note when the turn signal is shifted right or left, the dashboard indicators (little green arrows) do NOT come on at all. IS there another blinker relay can or do I have a problem somewhere else ? Thanks Pete
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Apr 23, 2008, 12:13 PM
Post #2 of 10
(1312 views)
|
|
Re: turnsgnal dont Blink
|
Sign In
|
|
Flasher On your 2000 Buick Century 3.1L SFI OHV , the Flasher is located:  Top rear right side of the engine
That's where AutoZone says it is. It probably is that, that is bad,
T
|
|
| |
|
|
Double J
Veteran
/ Moderator
Apr 23, 2008, 3:54 PM
Post #3 of 10
(1309 views)
|
|
Re: turnsgnal dont Blink
|
Sign In
|
|
That has to be a misprint Tom...
Flashers are usually put closest to the driver so as to be most audible to the driver(s)
I would check up at the top portions of the steering column area,left or right side
May have to remove the trim panel(s) under the steering column to access
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Apr 23, 2008, 5:03 PM
Post #4 of 10
(1305 views)
|
|
Re: turnsgnal dont Blink
|
Sign In
|
|
Must have been a typo Jim as that was copy and paste work - I didn't write that? Makes much more sense that it be where it can be heard and usually under dash somewhere over where the pedals are on most cars in general.
Pete: Keep looking. Have you taken the one out for the four ways to see if they stopped - that might be the one perhaps?
T
|
|
| |
|
|
way2old
Veteran
/ Moderator
Apr 23, 2008, 5:14 PM
Post #5 of 10
(1303 views)
|
|
Re: turnsgnal dont Blink
|
Sign In
|
|
Maybe this will help a little. According to Alldatapro, the flashers are one and the same.
 
- Remove the LH instrument panel (IP) insulator.
- Remove the steering column tiller panel.
- Grasp the hazard and turn signal flasher and slide the flasher to the right to release the flasher tabs from the slots on the BCM bracket.
- Disconnect the electrical connector from the hazard and turn signal flasher.
Being way2old is why I need help from younger minds
(This post was edited by way2old on Apr 23, 2008, 5:17 PM)
|
|
| |
|
|
Double J
Veteran
/ Moderator
Apr 23, 2008, 5:18 PM
Post #6 of 10
(1300 views)
|
|
Re: turnsgnal dont Blink
|
Sign In
|
|
Yea I know you didnt write it Tom..
I knew it was copy and paste..
Thats only the 2nd time I've seen a misprint by them..they're usually are right on.
Cant complain for the free info they provide all of us.
|
|
| |
|
|
PeteOh
New User
Apr 23, 2008, 5:31 PM
Post #7 of 10
(1297 views)
|
|
Re: turnsgnal dont Blink
|
Sign In
|
|
Wow ! I am a first time user here and you guys are awesum. You would think this should be easy. I did take the dashboard and steel plate off and got a real good look around and I could only see the ONE for the four way. Yes you are right the parts guy said they are both the same, they should be together, I plugged my new one into the 4 way socket and it fits, it works ( the 4-ways) but not the turn signals. The drawing from Mr way2old looks EXACTLY like my car Even down to the 3 channel like slots for the relays to go in BUT I only see one. SINCE the drawing looks so good I will give it another shot tomarrow and I will follow the wiring harness and double ck myself. THANKS PS how old is "way2old" I work with some pretty old guys and have hopes of getting way too old Pete
|
|
| |
|
|
Double J
Veteran
/ Moderator
Apr 23, 2008, 5:40 PM
Post #8 of 10
(1296 views)
|
|
Re: turnsgnal dont Blink
|
Sign In
|
|
Depends on what you consider "old" ..
I too years ago used to work with some"pretty old guys"
Then when I got to their age,i realized that "Hey ,That Ain't Old"
We're all like Jack Benny...29 and holding...
BTW..I think I speak for all when I say..."FIRST TIME USERS HAVE TO BUY THE FIRST ROUND"
(This post was edited by JIM N on Apr 23, 2008, 5:47 PM)
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Apr 24, 2008, 1:14 AM
Post #9 of 10
(1289 views)
|
|
Re: turnsgnal dont Blink
|
Sign In
|
|
LMAO! You know you can google "Maker's Mark" and get to CarJunky! Pete - didn't you see the box where it says you have to buy when you signed up if any of us have a clue about your car?
T
|
|
| |
|
|
way2old
Veteran
/ Moderator
Apr 24, 2008, 4:48 PM
Post #10 of 10
(1282 views)
|
|
Re: turnsgnal dont Blink
|
Sign In
|
|
HELL YEAH!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Age is dependant on which way you are looking. When I went into managment, the techs said I was way too old to work anymore. I just modified it to way2old. You might have a problem with the turn signal/4 way switch. I am assuming the brake lights work also? See if this helps any.
Being way2old is why I need help from younger minds
(This post was edited by way2old on Apr 24, 2008, 4:57 PM)
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
Drive Shaft Repair
2006 Toyoto Camry XLE Driver Side Electric Window Trouble
Grounding Cable, 2017 Jeep Renegade Trailhawk
equipment
Howdy
