|
|
Speedometer stopped working
|
|
|
| |
|
|
mrclean816
User
Nov 15, 2009, 3:37 PM
Post #1 of 7
(1301 views)
|
|
Speedometer stopped working
|
Sign In
|
|
1992
GMC
Sonoma
4.3l
150,000 miles
I was hearing this clicking sound coming from the 4x4/2wd stick while it was in the 2wd selector.
The clicking stops and all the sudden the speedometer reads 0.
Is this something I can fix myself or do I need to go to a mechanic.
Thanks
Robert
|
|
| |
|
|
mrclean816
User
Nov 17, 2009, 3:42 PM
Post #2 of 7
(1282 views)
|
|
Re: Speedometer stopped working
|
Sign In
|
|
bump bump
anyone?
|
|
| |
|
|
Loren Champlain Sr
Veteran
/ Moderator
Nov 17, 2009, 7:27 PM
Post #3 of 7
(1278 views)
|
|
Re: Speedometer stopped working
|
Sign In
|
|
mrclean; bump, bump. LOL. This vehicle uses a VSS (vehicle speed sensor) rather than a speedometer 'cable'. Usually, the VSS is the culprit with speedometer issues. But, doesn't explain the 'clicking' noise. Since I'm not a 'transmission' guy, I don't know if it uses a driven gear in the trans. I assume that you've tried changing the transfer case into different gears? 4L, 4H, and back to 2wd?
Loren
SW Washington
|
|
| |
|
|
mrclean816
User
Nov 17, 2009, 8:30 PM
Post #4 of 7
(1277 views)
|
|
Re: Speedometer stopped working
|
Sign In
|
|
thanks for the reply
since it was making noise i was wondering if it did have to do with a "gear" of some sorts.
I tried 4h and 2wd, but not 4L
|
|
| |
|
|
dixie4run
New User
Nov 21, 2009, 1:47 PM
Post #5 of 7
(1269 views)
|
|
Re: Speedometer stopped working
|
Sign In
|
|
Yes the VSS is gear driven but has nothing to do with the tranny per say, though that is where it is located. It is a very simple check,from under the vehicle driver side of tranny about 6-8 inches in front of where drive shaft emerges there is a plug with a two wire connector, the piece that comes out of the tranny is about 2-2.5 inches in diameter with 1 10mm bolt holding a Y or U type clamp. remove the 1 bolt and clamp and pull out the gear sleeve VSS combo and check the gear that is on the end, if worn get replacement from dealer probably 5-10 dollars.BE CAREFUL WHEN PULLING GEAR ASSEMBLY THERE IS A POTENTIAL FOR FLUID LOSS, MAY LOOK LIKE A LOT BUT NOT DANGEROUS UNLESS IT RUNS IN YOUR FACE.If gear is worn put your finger inside the hole where the gear sleeve was and feel for the drive gear on the tranny output shaft it could be worn also if it is it won't do any good to replace the driven gear, you should take to a good mechanic or transmission shop to have speedo drive and driven gears replaced, shouldn't be very expensive possibly in the 50-75 dollar range.
|
|
| |
|
|
mrclean816
User
Nov 21, 2009, 4:20 PM
Post #6 of 7
(1263 views)
|
|
Re: Speedometer stopped working
|
Sign In
|
|
oop, forgot to mention I fixed it.
for some reason the cables ran right next to a drive shaft joint.
The noise was the cables hitting up against the joint.
Then the cable came unplugged.
I just plugged it back in and stuffed it under some stuff so it wont do that again.
|
|
| |
|
|
way2old
Veteran
/ Moderator
Nov 21, 2009, 5:27 PM
Post #7 of 7
(1256 views)
|
|
Re: Speedometer stopped working
|
Sign In
|
|
Thanks for the fix post. We do not get nearly enough of those.
Being way2old is why I need help from younger minds
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
mdma pills for sale : WhatsApp +33758633852
Drive Shaft Repair
2006 Toyoto Camry XLE Driver Side Electric Window Trouble
Grounding Cable, 2017 Jeep Renegade Trailhawk
equipment
