Connect

Car Pictures

Shopping

Classifieds

News & Articles

Car Forums

Automotive Links

(Bookmark CarJunky)

	Auto Repair Home	SEARCH POSTS	WHO'S ONLINE	LOG IN

Automotive Repair Car Troubleshooting Topics   Car Troubleshooting   Engine Troubleshooting   Engine Fault Codes   Electrical and Wiring   Transmission Problems Car Repair Topics   Car Making Noises   Car Stereo Repair   Heating or AC Issues   Motorcycles and ATVs   Tricks of the Trade   Truck Repair Advice Site Options:      Login   Sign up here! Latest Forum Post     Car idles funny but doesn't throw codes 2006 Hyundai Elantra Engine size: 2.0L m...   Rear brake retaining clips 2015 Toyota Camry. I bought Import Direc...   Sanded rotors (deep scratches) I'm new to the forum and I have a couple...   2010 Mazda 3 Electrical Going On and Off while driving I drive a 2010 Mazda 3. It's always been...   Code P0193 Fuel Rail Pressure Sensor Circuit High Bank 1 2004 Ford E-350 Super Duty Ext Cargo Van...   speedometer wild deflections; sometime pump gas 1999 Gmc Savana, rwd, 5.7 (I think) v8 ...   Car stalling problem My 2013 hyundai started losing power whe...   2018 Kia soul. Knocking while accelerating. Hello, my 2018 Kia soul started making t...     2005 Buick Lesabre surging My 2005 Buick Lesabre runs good & th... Misfire on coil E I am new to this forum. I haven't figure...

1995 wrangler ignition switch removal Sign up here! Search this forum this category all forums for All words Any words Whole Phrase (search options) Auto Repair Home>> Automotive Repair>> Automotive Wiring and Electrical jacjm313 New User Feb 19, 2008, 7:22 AM Post #1 of 4 (4285 views) 1995 wrangler ignition switch removal Sign In i am trying to remove the ignition key cylinder from a 1995 jeep wrangler, and also the multi-func. stalk. they both operate intermittently.i removed the lock plate and signal actuator, however, i am stuck trying to remove the key cylinder. i have a haynes manual, but it's not specific enough (natch). any advice on what to push (pull, slide, lift,etc.) would be truly appreciated. any other helpful hints on this project is nice,toothx- jacjm313@aol.com Double J Veteran / Moderator Feb 19, 2008, 3:44 PM Post #2 of 4 (4270 views) Re: 1995 wrangler ignition switch removal Sign In Some have a retaining tab to push in others have a retaining screw... This link is not for a wrangler but for a Cherokee..but it will give you some idea....click Let me know if it helped ... jacjm313 New User Feb 19, 2008, 7:00 PM Post #3 of 4 (4267 views) Re: 1995 wrangler ignition switch removal Sign In i haven't tried it yet, but it looks like the right procedure. i left the buzzer switch in so i'm hoping there's a screw underneath it- thx for the info! jacjm313 New User Feb 20, 2008, 3:24 PM Post #4 of 4 (4260 views) Re: 1995 wrangler ignition switch removal Sign In i must have been trying too hard, but after i looked at the pix some more, i realized it WAS the black thingy at the bottom of said slot. sure was hard to push in tho, thanks for the help! any info on removing the ig. switch actuating arm???   Automotive Repair     Auto Body Repair and Refinishing     Heating or AC Issues     Electrical and Wiring     Brake Systems     Car Stereo Repair Advice     General Discussions     Car Making Funny Noises     Engine Fault Codes     Engine Troubles     Exhaust Systems     Steering and Suspension     Transmission Troubles     Tricks of the Trade Automotive World     General Discussions     Antique Car Talk     Car Shows and Events     The Bargin Bin     Motor Vehicle Inspection     Car Care Tips     Traffic Tickets     Gasoline, Motor Oils, Concept Cars and Engines     Auto Insurance, Financing, Leases, Warranties Truck Repair     General Discussions     Truck Engine Repair     Truck Suspension Repair Motorcycle Repair     General Discussions     Motorcycle Engine Repair CarJunky     Open Posting     Board FAQ's     New Board Suggestions

Search this forum this category all forums for All words Any words Whole Phrase (options)

Privacy Sitemap