Connect

Car Pictures

Shopping

Classifieds

News & Articles

Car Forums

Automotive Links

(Bookmark CarJunky)

	Auto Repair Home	SEARCH POSTS	WHO'S ONLINE	LOG IN

Automotive Repair Car Troubleshooting Topics   Car Troubleshooting   Engine Troubleshooting   Engine Fault Codes   Electrical and Wiring   Transmission Problems Car Repair Topics   Car Making Noises   Car Stereo Repair   Heating or AC Issues   Motorcycles and ATVs   Tricks of the Trade   Truck Repair Advice Site Options:      Login   Sign up here! Latest Forum Post     Car idles funny but doesn't throw codes 2006 Hyundai Elantra Engine size: 2.0L m...   Rear brake retaining clips 2015 Toyota Camry. I bought Import Direc...   Sanded rotors (deep scratches) I'm new to the forum and I have a couple...   2010 Mazda 3 Electrical Going On and Off while driving I drive a 2010 Mazda 3. It's always been...   Code P0193 Fuel Rail Pressure Sensor Circuit High Bank 1 2004 Ford E-350 Super Duty Ext Cargo Van...   speedometer wild deflections; sometime pump gas 1999 Gmc Savana, rwd, 5.7 (I think) v8 ...   Car stalling problem My 2013 hyundai started losing power whe...   2018 Kia soul. Knocking while accelerating. Hello, my 2018 Kia soul started making t...     2005 Buick Lesabre surging My 2005 Buick Lesabre runs good & th... Misfire on coil E I am new to this forum. I haven't figure...

1986 isuzu II starter switch Sign up here! Search this forum this category all forums for All words Any words Whole Phrase (search options) Auto Repair Home>> Automotive Repair>> Automotive Wiring and Electrical taylortbutts New User Dec 10, 2008, 9:48 AM Post #1 of 3 (1235 views) 1986 isuzu II starter switch Sign In 1986 Isuzu trooper II 2.3 , 224,000mi. Had starter bench tested, checks ok. Wire leading from ignition to starter reads 13.5v. but won't turn over starter. If jumped from battery to starter it works fine. Not enough amps into starter? Need bigger guage wire? thanks Loren Champlain Sr Veteran / Moderator Dec 10, 2008, 6:01 PM Post #2 of 3 (1228 views) Re: 1986 isuzu II starter switch Sign In The large wire (battery cable) will show battery voltage, of course. You need to see if you are getting 12V to the small (exciter) wire with the ign. switch in the crank (start) mode. Loren SW Washington taylortbutts New User Dec 11, 2008, 5:40 AM Post #3 of 3 (1223 views) Re: 1986 isuzu II starter switch Sign In Yes the primary is hot 12v. It's the exiciter that I was refering to in my post. With the ignition switch turned on, the exiciter wire is hot also 12v. Still it does'nt have enough something to throw the starter. Thanks   Automotive Repair     Auto Body Repair and Refinishing     Heating or AC Issues     Electrical and Wiring     Brake Systems     Car Stereo Repair Advice     General Discussions     Car Making Funny Noises     Engine Fault Codes     Engine Troubles     Exhaust Systems     Steering and Suspension     Transmission Troubles     Tricks of the Trade Automotive World     General Discussions     Antique Car Talk     Car Shows and Events     The Bargin Bin     Motor Vehicle Inspection     Car Care Tips     Traffic Tickets     Gasoline, Motor Oils, Concept Cars and Engines     Auto Insurance, Financing, Leases, Warranties Truck Repair     General Discussions     Truck Engine Repair     Truck Suspension Repair Motorcycle Repair     General Discussions     Motorcycle Engine Repair CarJunky     Open Posting     Board FAQ's     New Board Suggestions

Search this forum this category all forums for All words Any words Whole Phrase (options)

Privacy Sitemap