Main IndexAuto Repair Home Search Posts SEARCH
POSTS
Who's Online WHO'S
ONLINE
Log in LOG
IN









Search Auto Parts

ABS problems...I think


  Email This Post



clunker
Novice

Sep 8, 2009, 7:51 AM

Post #1 of 9 (1537 views)
ABS problems...I think Sign In

I have a 1997 Chevrolet S-10(4 cyclinder) with approx. 90K miles. A couple of weeks ago my ABS light came on right after start up. Since then, the break peddle kicks back and there's a grinding/vibrating/slipping just before I come to a complete stop. This is an intermittent problem as it doesn't happen all the time. My rotors and breaks are fine. Could a ABS sensor cause this and if so, how can I disable the ABS system until I can get the money to repair it?


Hammer Time
Ultimate Carjunky / Moderator
Hammer Time profile image

Sep 8, 2009, 9:38 AM

Post #2 of 9 (1529 views)
Re: ABS problems...I think Sign In

Yes, that's usually what causes it. The issue is that one of the sensors is not accurate and when coming to a stop the ABS module sees one wheel going slower so it thinks it's locking up and it releases that brake. that's what the pedal buzzing is.

You can disable it by removing the fuse but the ABS light will remain on.



~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.



clunker
Novice

Sep 8, 2009, 10:02 AM

Post #3 of 9 (1524 views)
Re: ABS problems...I think Sign In

Thank you. I assumed that was the problem but wasn't 100% sure. Would you recommend changing the sensors myself or letting a professional handle this one? I'm usually a do-it-myselfer but I'm not familiar at all with ABS. I assume I'll have to have a diagnostics ran to troubleshoot which sensor is giving me problems. If the sensors are simple to change out then doing it myself is the route I'd prefer to go with.


Hammer Time
Ultimate Carjunky / Moderator
Hammer Time profile image

Sep 8, 2009, 10:08 AM

Post #4 of 9 (1520 views)
Re: ABS problems...I think Sign In

Is it 2WD or 4WD?



~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.



clunker
Novice

Sep 8, 2009, 10:33 AM

Post #5 of 9 (1514 views)
Re: ABS problems...I think Sign In

2WD.


Hammer Time
Ultimate Carjunky / Moderator
Hammer Time profile image

Sep 8, 2009, 10:49 AM

Post #6 of 9 (1511 views)
Re: ABS problems...I think Sign In

On the 4WD, it's part of the hub bearing but the 2WD takes regular 2 piece bearings so the sensor appears to be separate. The flat rate calls for just under an hour to change it. The caliper and rotors have to be removed to access itso it doesn't look too hard. As you said though, your going to need someone to diagnose which one it is..



~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.



clunker
Novice

Sep 8, 2009, 10:52 AM

Post #7 of 9 (1506 views)
Re: ABS problems...I think Sign In

Also, I have tried to locate the ABS fuse. I thought it would be located in the drivers side fuse panel but I don't see anything that refers to ABS. Is it located somewhere else or am I just blind?


Hammer Time
Ultimate Carjunky / Moderator
Hammer Time profile image

Sep 8, 2009, 11:01 AM

Post #8 of 9 (1503 views)
Re: ABS problems...I think Sign In

In the underhood fuse box, look for fuse #12 which is 10A marked brake. This may take out your brake lights though so if it does your going to have to go to the fusible link in the engine compartment. It's a gray fusible link on a red wire. It should be attached to the power distribution box.



~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.



clunker
Novice

Sep 8, 2009, 12:17 PM

Post #9 of 9 (1495 views)
Re: ABS problems...I think Sign In

Thanks a lot. You've been more than helpful.






  Email This Post
 
 


Feed Button




Search for (options) Privacy Sitemap