drum brake question - Brake Repair Help


	Auto Repair Home	SEARCH POSTS	WHO'S ONLINE	LOG IN

Automotive Repair

Car Troubleshooting Topics
  Car Troubleshooting
  Engine Troubleshooting
  Engine Fault Codes
  Electrical and Wiring
  Transmission Problems

Car Repair Topics
  Car Making Noises
  Car Stereo Repair
  Heating or AC Issues
  Motorcycles and ATVs
  Tricks of the Trade
  Truck Repair Advice

Site Options:
  Login
  Sign up here!

Latest Forum Post

Lukewarm Heat............

New antifreeze reverse flush heater core...

multiple warning lights

2013 GMC Terrain 130,000 miles 4 cylinde...

2014 Nissan Sentra Shaking

Car recently started shaking when accele...

Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086

N/A

1989 toyota pickup 3.0 crank no start

I have a 1989 toyota pickup 3.0 crank no...

Strut spring orientation and strut mount tension nut

2017 Nissan rogue awd 2.5 L Put in Monro...

Transmission stuck in part, I have tried everything

So I'm working on my elderly fathers 201...

2017 dodge journey LED headlights on/off randomly

Year of vehicle 2017 Make of vehicle dod...

Kia Soul starter replacement issues!

Okay so my car is a 2010 Kia soul 2.0 en...

Please Help - Knock sound & engine fail

Hi all, Hoping to get some insight and ...

drum brake question

Sign up here!

Search for (search options)

Auto Repair Home>> Automotive Repair>> Brake Repair Help

Rolomoto
New User

Sep 22, 2013, 8:03 PM

Post #1 of 3 (1540 views)

drum brake question	Sign In

Hi,
I'm doing the rear brakes on a '95 tercel and when I pulled the drums off there was a lot of grease on the end of the axle as well as in the hub (where the inner wheel bearing is). I wiped a lot of it away and was wondering where to put new grease. Should I apply it to the axle or put it in the hub?
Thanks

Hammer Time
Ultimate Carjunky / Moderator
Hammer Time profile image

Sep 23, 2013, 2:44 AM

Post #2 of 3 (1520 views)

Re: drum brake question	Sign In

The bearings themselves should be packed with grease internally with some extra inside the drum on the race before it is put back together. There should be nothing outside of the seal or anywhere near the brake or drum surface.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.

Tom Greenleaf
Ultimate Carjunky / Moderator
Tom Greenleaf profile image

Sep 23, 2013, 2:47 AM

Post #3 of 3 (1519 views)

Re: drum brake question	Sign In

Hmmm - I thought by '95 greaseable bearing were done for hubs you can't mess with but no problem. The "inner/outer bearing" idea is still out there now mostly trailers. Was the norm for almost every non drive wheel for ages on top of ages.

You grease the bearings themselves each leaving just some in hub and on axle, install a new grease seal, set adjustment them with the nut*, install new cotter pin or however it's locked, put dust cap back on and not worry about it too much unless there's a problem. Grease should never be allowed on the brake.

Someone before you might have been a bit heavy with the grease which really shouldn't be a problem. Is there a problem? Why were you in there to begin with and you do need to for even inspecting brakes and some will suggest periodic re-greasing that type bearing concept and should for some depending on use, miles or time.

This is so primal it pre dates cars at all. Wooden wheels on the carts pulled by horses did this that way. Trouble now is everyone forgot and it requires setting them and knowing how or you will cause problems. Too tight they'll burn out and can spray grease around as that makes them too hot also. Too loose with free play the integrity is lost, brake may not behave properly depending on how far off it is.

There will be listed torque specs for how tight to set them with that nut and back off some % of a turn type thing. Why are you in there?

T

Search for (options) Privacy Sitemap