Connect

Car Pictures

Shopping

Classifieds

News & Articles

Car Forums

Automotive Links

(Bookmark CarJunky)

	Auto Repair Home	SEARCH POSTS	WHO'S ONLINE	LOG IN

Automotive Repair Car Troubleshooting Topics   Car Troubleshooting   Engine Troubleshooting   Engine Fault Codes   Electrical and Wiring   Transmission Problems Car Repair Topics   Car Making Noises   Car Stereo Repair   Heating or AC Issues   Motorcycles and ATVs   Tricks of the Trade   Truck Repair Advice Site Options:      Login   Sign up here! Latest Forum Post   Please Help - Knock sound & engine fail Hi all, Hoping to get some insight and ...   03 alero no low speed blower Good day everyone, I have a 2003 Olds a...   04 Chevy 2500hd tail light issues Help!!! I have changed my combo switch...   1999 Grand Caravan Sport not starting. Hi. I'm new here. I hope someone can hel... Brake Seals Bulging 2021 Toyota Corolla LE 1.8l 65,000 mile...   Engine blew up after oil change, is mechanic responsible? Hello, I have a 2007 Hyundai Elantra wit...   Changed pads and now brake pedel goes to the floor I am not much of a mechanic, and needed ...   Equinox air conditioning issue, help please! I have a 2020 Chevrolet Equinox that has...   2005 Maxima overheats only when idling but engine temp comes down immediately if I rev up the engine (even though car is stationary) hello everyone, I own a 2005 Nissan M...   Brake & Turn Signal Out - One side only 2002 Ford Ranger 3.0 V6, 5-speed manual ...

Manual transmission won't engage Sign up here! Search this forum this category all forums for All words Any words Whole Phrase (search options) Auto Repair Home>> Automotive Repair>> Transmission Problems jeffreyinmilw New User Jun 17, 2008, 4:47 PM Post #1 of 3 (6660 views) Manual transmission won't engage Sign In I recently had a new clutch, slave cylinder and master cylinder installed on my 2001 Ford Ranger. The flywheel was also machined. Two weeks later the original symptoms appeared again, namely difficulty in engaging gears. They bled the lines and it worked for another 2 weeks. This time they replaced the master cylinder. Now two weeks later the problems arose again. It is an intermittent problem usually occurring at first start up in the morning and after extended highway usage. Sometimes in order to engage I have to turn the truck off and then it slides easily into gear. Any ideas? dave284 Enthusiast Jun 17, 2008, 8:59 PM Post #2 of 3 (6655 views) Re: Manual transmission won't engage Sign In The problem could be in the trans itself....need to check the oil level...I think by removing the speed gear...not too sure on that one, if thats ok then need to check for leaks and adjustments on brake pedal......also there could have got some trash in the lines too, and last thing there is a certain procedure to bleeding a master cylinder when installing. DanD Veteran / Moderator Jun 18, 2008, 4:40 AM Post #3 of 3 (6651 views) Re: Manual transmission won't engage Sign In Make sure the proper oil was used in the transmission; most of the Rangers take automatic transmission fluid (Mercon). Dan. Canadian "EH"   Automotive Repair     Auto Body Repair and Refinishing     Heating or AC Issues     Electrical and Wiring     Brake Systems     Car Stereo Repair Advice     General Discussions     Car Making Funny Noises     Engine Fault Codes     Engine Troubles     Exhaust Systems     Steering and Suspension     Transmission Troubles     Tricks of the Trade Automotive World     General Discussions     Antique Car Talk     Car Shows and Events     The Bargin Bin     Motor Vehicle Inspection     Car Care Tips     Traffic Tickets     Gasoline, Motor Oils, Concept Cars and Engines     Auto Insurance, Financing, Leases, Warranties Truck Repair     General Discussions     Truck Engine Repair     Truck Suspension Repair Motorcycle Repair     General Discussions     Motorcycle Engine Repair CarJunky     Open Posting     Board FAQ's     New Board Suggestions

Search this forum this category all forums for All words Any words Whole Phrase (options)

Privacy Sitemap