Main IndexAuto Repair Home Search Posts SEARCH
POSTS
Log in LOG
IN









Ford Fusion (1st gen)


Search for (search options)
 



Jadawa66
Novice

Nov 23, 2025, 12:02 PM

Post #1 of 12 (143043 views)
Ford Fusion (1st gen) Sign In

08 Lincoln MKZ 3.5 V6 2WD (Fancy Fusion) 180k

Great car, bought in Utah on a trip. Rust free, drove 4k around the country back to Michigan 3 years ago. Used as a gas saver daily to work, the morning it went bad.

55 mph ½ way to work, she starts to misfire a bit, like it dropped a cylinder or two. Ok, i hadn't done a tune up since owning it, so maybe it's overdue? I pull over, check wires, all looks good, might as well get to work. I hit autozone for a code read coming home, coil pack 1 & 2. Not surprising. I get a phone call as I leave, I sit there maybe 5 minutes finishing the call and the car died. Dang. It wouldn't start after that. That was this May. I've been so busy, I'm now getting to troubleshoot it. A mechanic did look at it, but all he did was kill the battery, not finding anything. I replaced it and the key fob. The old battery was so bad the Ford security red lock light wouldn't go away. All fuses look good. Does anyone have a fuel pump and igniter schematic for starters?


Hammer Time
Ultimate Carjunky / Moderator
Hammer Time profile image

Nov 23, 2025, 6:01 PM

Post #2 of 12 (142984 views)
Re: Ford Fusion (1st gen) Sign In

That's not how to approach this. There is a series of tests that isolate the problem. Just a wild suspicion I have is that it jumped the timing belt. A compression test would show that.

All "crank, no start" conditions are approached in the same way. Every engine requires certain functions to be able to run. Some of these functions rely on specific components to work and some components are part of more than one function so it is important to see the whole picture to be able to conclude anything about what may have failed. Also, these functions can ONLY be tested during the failure. Any other time and they will simply test good because the problem isn't present at the moment.
If you approach this in any other way, you are merely guessing and that only serves to replace unnecessary parts and wastes money.



Every engine requires spark, fuel and compression to run. That's what we have to look for.

These are the basics that need to be tested and will give us the info required to isolate a cause.

1) Test for spark at the plug end of the wire using a spark tester. If none found, check for power supply on the + terminal of the coil with the key on.


2) Test for injector pulse using a small bulb called a noid light. If none found, check for power supply at one side of the injector with the key on.


3) Use a fuel pressure gauge to test for correct fuel pressure, also noticing if the pressure holds when key is shut off.

4) If all of these things check good, then you would need to do a complete compression test.

Once you have determined which one or combination of these functions has dropped out,
you will know which system is having the problem.



~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.



Jadawa66
Novice

Nov 23, 2025, 7:19 PM

Post #3 of 12 (142976 views)
Re: Ford Fusion (1st gen) Sign In

Thank you for that response Hammertime! I didn't think of it that way. I do need to brush up on how to follow those steps. I'll let you know what I find out.


Hammer Time
Ultimate Carjunky / Moderator
Hammer Time profile image

Nov 23, 2025, 7:23 PM

Post #4 of 12 (142975 views)
Re: Ford Fusion (1st gen) Sign In

Those are some pretty basic tests. Given the way yours acted you might want to start with the compression test.



~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.



Jadawa66
Novice

Nov 28, 2025, 5:01 PM

Post #5 of 12 (142505 views)
Re: Ford Fusion (1st gen) Sign In

Tried to write back a couple times and I've hit the wrong button and deleted what I said accidentally lol 😠

Just thoughts and ponders. This is a chain and gear set up. Is it still just as likely to slip? There was no catastrophic sounds (metal on metal, clanking, etc) or smoke when the problem started, thank goodness.

I've done a poorman's spark check on the no.5 coil and plug, by grounding the ground electrode. There's too much plastic, I have to run wire with an aligator clip on each end to the electrode and a good strut nut for ground. NO SPARK. I need to check the whole front bank.

Fuel: I borrowed the psi kit from autozone, still haven't the slightest where to hook it up yet. Mind you, I'm doing what I can in between holiday crap. I got under the front rt passenger foot compartment, verified the inertia switch is closed. I wasn't sure i was hearing the main fuel tank fuel pump, as opposed to the direct injection fuel pump for the fuel rails. So I disconnected the fuel line that goes to the U - shape rail that goes to said injectors. With key to ON I get a good 1 shot of fuel, then with key to start, it'll pump as long as i hold it, so that's good.

That fuel line, runs down the firewall as well as anything with the backside bank, i can't see crap because of the intake being molded over that way. The fuel pressure switch is probably down there. Luckily the car is on a lift and i just got to lift it when im done screwing around up top for a bit.


Hammer Time
Ultimate Carjunky / Moderator
Hammer Time profile image

Nov 28, 2025, 5:13 PM

Post #6 of 12 (142500 views)
Re: Ford Fusion (1st gen) Sign In

Your car doesn't have an igniter. The PCM controls the coils.

Your fuel pump test helps but it's not very accurate.

It would be helpful to know if you have injector pulse and power supply to the injectors to help further isolate things.

The Crank sensor is one possibility but the other tests would have been help in that area.

If you have a tach in the car or scan tool that reads data you can check for RPM during cranking which would be a further indicator of a bad crank sensor if there is no RPM.



~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.



Jadawa66
Novice

Nov 28, 2025, 5:29 PM

Post #7 of 12 (142496 views)
Re: Ford Fusion (1st gen) Sign In

Igniter? Isn't that diesel speak?

Copy on the injector pulse and pwr supply. I appreciate your insight.

Yes, it has an rpm gage in the dash. No scan tool at the moment, though.


Hammer Time
Ultimate Carjunky / Moderator
Hammer Time profile image

Nov 28, 2025, 5:51 PM

Post #8 of 12 (142487 views)
Re: Ford Fusion (1st gen) Sign In

You asked for fuel pump and igniter schematics. Doesn't have igniter.

If it has an RPM gauge, see if it moves a little during cranking.



~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.



Jadawa66
Novice

Nov 28, 2025, 6:53 PM

Post #9 of 12 (142475 views)
Re: Ford Fusion (1st gen) Sign In

You got me there man. Indeed I did. I'll be the 1st to admit I don't always get it right either.

I meant injectors. I see others talking about reading from the injectors. Just not for this type of vehicle and problem.

Not much literature I've found for top end troubleshooting on these Fusion platforms for as popular as they are. The Flex, Edge, and Fusion are mostly the same underpinnings, times 3 manufacture plates.


Hammer Time
Ultimate Carjunky / Moderator
Hammer Time profile image

Nov 28, 2025, 7:03 PM

Post #10 of 12 (142473 views)
Re: Ford Fusion (1st gen) Sign In

Just because it uses a Fusion platform, it's not a Fusion. It's it's own vehicle.

I have a wiring diagram but it's spread over 4 pages.

The power supply for the injectors is on the violet with green wire.
The trigger wires for the injectors are different colors for each cylinder.



~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.



Jadawa66
Novice

Sep 22, 2026, 12:32 PM

Post #11 of 12 (96009 views)
Re: Ford Fusion (1st gen) Sign In

The #1 coil pack was found to be blown up. Shorted at primary read and high resistance at the 2ndary read. Now, I researched and found there is a Ford Technical Bulletin on this. If you find this and a code, like i did, you may have to change your PCM at the same time, because the circuit for the firing in the PCM will get fried as well! There is troubleshooting to dictate your next steps. Waiting a new coil and PCM now. Hope this might help anybody with similar issues. Codes were p0351 = coil #1 issues and c0607 = check engine lt illuminated under one or multiple conditions.





Hammer Time
Ultimate Carjunky / Moderator
Hammer Time profile image

Sep 22, 2026, 12:39 PM

Post #12 of 12 (96008 views)
Re: Ford Fusion (1st gen) Sign In

This is nothing new or unusual. Any time a coil or it's operating circuit shorts out it can take out the coil driver in the computer. Those drivers can't handle high current load. Glad you got it figured out.



~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.







 
 
 






Search for (options) Privacy Sitemap