|
|
LincolnsSuck
User
Sep 4, 2017, 7:08 PM
Post #1 of 9
(1589 views)
|
|
Crankshaft oil seal
|
Sign In
|
|
Im changing out my crank shaft oil seal. Im pretty sure this is the issue as oil is slinging all over my engine and getting on my belt. I have to torque off the gigantic bolt that holds my crankshaft pulley. I have to use an impact and in order to get the impact on the bolt i must remove my eadiator. However, i have transmission cooling lines attachrd to my radiator and i cant break them off to proceed. Any suggestions? Pic related. I own a 99 lincoln towncar v8 4.6
|
|
| |
|
|
LincolnsSuck
User
Sep 4, 2017, 7:12 PM
Post #2 of 9
(1587 views)
|
|
Re: Crankshaft oil seal
|
Sign In
|
|
Well it wont let me post the picture. Its on the left aide of my radiator. Two rubber lines that have regular hose clamps on them. I removed the clamp but no matter how hard i pull i cant get the line to budge. I tried breaking it loose by jamming a flathead under it and that barely made a difference.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 4, 2017, 7:20 PM
Post #3 of 9
(1577 views)
|
|
Re: Crankshaft oil seal
|
Sign In
|
|
Twist it to break the seal.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
LincolnsSuck
User
Sep 5, 2017, 8:33 AM
Post #4 of 9
(1543 views)
|
|
Re: Crankshaft oil seal
|
Sign In
|
|
Okay. So i twisted and it worked. Now i have to remove what look like ac lines?
http://i68.tinypic.com/34ybl9v.jpg
Whenever i twist the nuts holding them on - a thick grwwn goop sprays out accompanied by some weird white gas. It almost sounds like it's hissing. Do i procees or is there a way to depressurise the line?
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Sep 5, 2017, 8:43 AM
Post #5 of 9
(1534 views)
|
|
Re: Crankshaft oil seal
|
Sign In
|
|
You need to recover the ac refrigerant if you are going to be disconnecting those lines. You don't need to disconnect those lines to remove the radiator, but now you have a leak and will need to replace the o rings.
It really appears like you don't know what your doing. Do you have service information on this? Does your ac system even work?
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Sep 5, 2017, 8:46 AM)
|
|
| |
|
|
LincolnsSuck
User
Sep 5, 2017, 8:51 AM
Post #6 of 9
(1526 views)
|
|
Re: Crankshaft oil seal
|
Sign In
|
|
Well im poor and learn from my mistakes. My ac does work. I only twisted it a little before closing it back and tightening it. I dont see another way to remove these lines. I need to get my whole radiator out. Condensor and all. Trying to make room to fit my impact in to remove the crankshaft
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 5, 2017, 11:03 AM
Post #7 of 9
(1513 views)
|
|
Re: Crankshaft oil seal
|
Sign In
|
|
Removing an AC condenser just to remove a crank pulley is just stupid.
You don't have the equipment or knowledge to do this job. Give up while you only messed up a little bit.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
LincolnsSuck
User
Sep 7, 2017, 9:04 AM
Post #8 of 9
(1491 views)
|
|
Re: Crankshaft oil seal
|
Sign In
|
|
Well i got the crank pulley out and replaced it. So that's good ! But now my Ac doesn't work and it nakes a distinctive humm when i engage it. Do you think it could be low on freon? Some did drain out when i opened those lines up. Thinking i depressurized the ac lines and a pumping in frwon would solve it
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Sep 7, 2017, 6:36 PM
Post #9 of 9
(1476 views)
|
|
Re: Crankshaft oil seal
|
Sign In
|
|
The best course of action is to have someone recover what is left in the system. Then replace the line o ring. Last have it vacuumed and recharged with the correct weight.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
1989 toyota pickup 3.0 crank no start
Please Help - Knock sound & engine fail
