|
|
freakTCHB
New User
Jan 25, 2012, 9:49 PM
Post #1 of 13
(2118 views)
|
i have a 94' ford tempo GL and i was recently in an accident (i was T-boned). so ive been looking for another car. i found a 94' ford probe GT that needs an engine. i was wondering if the engine out of my tempo will fit into the probe and fit properly?
1994 Ford Tempo GL
basic 2.3L (im pretty sure)
1994 Ford Probe GT
i have no idea what engine it has in it now, probably the factory one, which i think is a mazda 2.0 (wikipedia)
thanks for any help
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Jan 26, 2012, 2:50 AM
Post #2 of 13
(2090 views)
|
No! You aren't even sure what size engines you have so forget it is my suggestion,
T
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jan 26, 2012, 4:21 AM
Post #3 of 13
(2084 views)
|
The only thing it can be swapped with is the exact same engine and by the sounds of it, you don't wwant to attempt this yourself.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
seriousfreedom
User
Feb 21, 2012, 8:27 PM
Post #4 of 13
(1995 views)
|
i agree with cars these days there is no simple engine swap cause you have to have the ecm that goes for the engine who knows what else/
|
|
| |
|
|
nickwarner
Veteran
/ Moderator
Feb 21, 2012, 8:32 PM
Post #5 of 13
(1991 views)
|
Ford engineered the Tempo. Mazda engineered the Probe. Last time the two countries collided a few A-bombs went off. Picture the same thing except in your garage as you pull your hair out on something that will never work. Square pegs don't fit in round holes.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Feb 21, 2012, 8:35 PM
Post #6 of 13
(1988 views)
|
Not to mention, it would be against federal law to attempt it.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Feb 24, 2012, 7:14 PM
Post #8 of 13
(1968 views)
|
Making any changes whatsoever in the original configuration as it left the factory is considered emissions tampering. You can swap engines but only with the exact same replacement.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
seriousfreedom
User
Feb 24, 2012, 7:16 PM
Post #9 of 13
(1962 views)
|
oh ok so replacing my inline 6 in my dodge truck and putting in a v-8 would be in violation of that law then??
did not know that thanks for that info
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Feb 24, 2012, 7:23 PM
Post #10 of 13
(1958 views)
|
This is the last post on this. You need to stop hijacking other peoples threads.
Here is the law
The Statute
In the Clean Air Act and the Clean Air Act Amendments of 1990 Congress gave USEPA the authority to regulate mobile sources. In addition to requiring automakers to design automobiles that met increasingly stringent emissions limits, these laws also established provisions to prevent anyone from defeating those modifications. In a letter dated November 14, 1997, Steve Albrink of the Vehicle Programs & Compliance Division of the Office of Mobile Sources of USEPA wrote a letter providing a more accessible interpretation of USEPA's policy than that contained in the official USEPA interpretation, Memorandum 1A (Office of Enforcement and General Counsel, dated June 25, 1974, Mobile Source Enforcement Memorandum No. 1A, SUBJECT: Interim Tampering Enforcement Policy) and subsequent changes to that policy, including fining individuals as well as repair shops. Mr. Albrink's letter states:
The federal tampering prohibition is contained in section 203(a)(3) of the Clean Air Act (Act), 42 U.S.C. 7522(a)(3). Section 203(a)(3)(A) of the Act prohibits any person from removing or rendering inoperative any device or element of design installed on or in any motor vehicle in compliance with regulations under Title II of the Act (i.e., regulations requiring certification that vehicles meet federal emissions standards). The maximum civil penalty for a violation of this section by a manufacturer or dealer is $25,000; for any other person, $2,500. Accordingly, any change from the original certified configuration of a vehicle or engine, or the manufacture or sale of a non-original equipment aftermarket part or system could be considered a violation of section 203(a)(3) of the Act. This would include modifications to the fuel delivery system.
The Policy
So, according to USEPA, pretty much any modification to your vehicle that in any way alters anything from the intake air to the tailpipe exit constitutes tampering. In fact, USEPA has developed an extensive list of specific questions and answers detailing just how extreme this view is.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
(This post was edited by Hammer Time on Feb 24, 2012, 7:24 PM)
|
|
| |
|
|
seriousfreedom
User
Feb 24, 2012, 7:36 PM
Post #11 of 13
(1951 views)
|
i was just trying to understand what you was sayin about the federal law thing wasnt trying to hijack anyones thread just trying to understand it
|
|
| |
|
|
re-tired
Veteran
/ Moderator
Feb 25, 2012, 10:41 AM
Post #12 of 13
(1930 views)
|
It is possable to do a legal swap . even a v8 coinverson . but after reading the ENTIRE article , is it really worth it ., it would take a ton of money and time.
*
*
JTR Chevrolet S-10 Truck . California Smog Laws
LIFE'S SHORT GO FISH
|
|
| |
|
| | |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
2006 Toyoto Camry XLE Driver Side Electric Window Trouble
Tierod end change caused some kind of leak
Grounding Cable, 2017 Jeep Renegade Trailhawk
equipment
Howdy
