Main IndexAuto Repair Home Search Posts SEARCH
POSTS
Who's Online WHO'S
ONLINE
Log in LOG
IN









Search Auto Parts

1991 dodge dynasty


  Email This Post



Guest
Anonymous Poster
kenburton1966@yahoo.com

Jun 17, 2009, 9:36 AM

Post #1 of 4 (7830 views)
1991 dodge dynasty Sign In

1991 dodge dynasty(k car) has 3.2lt. had someone short computer and computer was replaced and now won't idle when cold and when hot stall on exceleration or decelleration. i have no idia what is causing this and hoping someone can point the direction. ran exalent before was shorted to computer. now new computer and runs realy rough.


Hammer Time
Ultimate Carjunky / Moderator
Hammer Time profile image

Jun 17, 2009, 10:13 AM

Post #2 of 4 (7826 views)
Re: 1991 dodge dynasty Sign In

Did you instal a "new" computer or a used computer?
Is the check engine light coming on at all?
.
.
.
.
.
.



~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.



Guest
Anonymous Poster
kenburton1966@yahoo.com

Jun 23, 2009, 12:24 AM

Post #3 of 4 (7806 views)
Re: 1991 dodge dynasty Sign In

Yes, I installed a used computer on my 1992 dodge
I believe the the check engine light is on. Thanks for coming back to me on this problem.


Hammer Time
Ultimate Carjunky / Moderator
Hammer Time profile image

Jun 23, 2009, 12:34 AM

Post #4 of 4 (7800 views)
Re: 1991 dodge dynasty Sign In

There is no way of knowing if you even have the right computer installed. If the check engine light is on, then the best place to start is reading the stored codes.

Diagnostic Trouble Codes - 1991
Chrysler


11
Engine has not been cranked since battery was disconnected.
12
Memory Standby power lost.
13
MAP sensor pneumatic circuit.
14
MAP sensor electrical circuit.
15
Vehicle speed/distance sensor.
16
Loss of battery voltage sense.
17
Engine running too cool.
21
Oxygen sensor circuit.
22 Coolant temperature sensor circuit.
23
Throttle body temperature sensor circuit.
24
Throttle position sensor.
25
AIS motor driven circuit.
26
Peak injector current not reached.
27
Fault in injector driver interface circuit.
31
Purge solenoid circuit.
32
On Calif. models, EGR diagnosis.
33
A/C cutout relay circuit.
34
Speed control solenoid driver circuit.
35 Fan control relay circuit.
37
Fault in part throttle unlock solenoid driver circuit.
41
Charging system excess or no field circuit.
42
ASD relay circuit.
43 Fault in ignition coil control circuit.
44
Loss of FJ2 to logic board.
46 Battery voltage too high.
47 Battery voltage too low.
51 Oxygen feedback system stuck at lean position.
52
Oxygen feedback system stuck at rich position.
53
Internal logic module problems.
54
Indicates a fault in the distributor high data rate pickup circuit.
55
Completion of fault code display.
62
Indicates unsuccessful attempt to update EMR mileage.
63
Unsuccessful attempt to write to an EEPROM location by the controller.
77
Speed control power relay circuit.


To call up codes, cycle ignition switch on, off, on, off and on within 5 seconds. Stored codes will be indicated by flashes of the power loss/check engine lamp. The codes will be indicated as two digit numbers, with a four second pause between codes. An example of a code is as follows:
  • Power Loss/Check Engine Lamp illuminated for approximately 2 to 3 seconds as a bulb check, then turns off.
  • Lamp flashes 2 times, pauses, then flashes 6 times.
  • Lamp pauses for approximately 4 seconds.
  • Lamp flashes 3 times, pauses, then flashes 1 time.

This would indicate that code 26 and 31 are stored. The lamp will continue to flash until all stored codes have been displayed.
Once the lamp starts flashing the stored fault codes, it cannot be stopped. If a code is missed, the entire procedure must be repeated. The lamp will not indicate if oxygen feedback system is switching lean-rich or if idle motor system is operational. The lamp also cannot be used to perform actuation test mode, sensor test mode or engine running test mode.
After all fault codes have been displayed, then power loss/check engine lamp can be used to verify switch function. The lamp will turn on and off as the switch is turned on and off.



~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.



(This post was edited by Hammer Time on Jun 23, 2009, 12:36 AM)






  Email This Post
 
 


Feed Button




Search for (options) Privacy Sitemap